There is a way to accomplish what you are needing to do. But the 7-way isn't going to play a role in charging your battery and doesn't care if the battery is lithium or not. The hot wire coming from your 7-way would only ever be enough to trickle charge your battery.
If you are wanting to charge your battery while under way you will need a DC-DC charger like the Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1225D.
You would also want a battery isolator like the Redarc Smart Start Battery... view full answer...
It is possible that the Dexter Trailer Axle w/ Idler Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs # 20545I-EZ-72-15 you were looking at will fit your 2012 Aliner Classic Camper but the only way to be sure it to measure your current axle, and find the axle rating of your current axle.
Starting with the measurements you will need to know the hub face to hub face and spring center to spring center measurements. For example the # 20545I-EZ-72-15 has a hub face to hub face... view full answer...
We do not carry the WFCO-8735-LiS, however I do have another alternative.
Instead, I recommend going with the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger # PD4135K.
This is designed to replace your WFCO-8735-P, and is compatible with lithium batteries. view full answer...
The Timbren Axle Less kit part # ASR35HDS05 would be your best option as it has a 4 inch lift built into it and has a 3,500 lb capacity. Then for idler hubs the part # 8-213-5UC1-EZ would be a great option which fit this spindle and also have a 6 on 5-1/2 inch bolt pattern. view full answer...
The grease that comes installed in the Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased # AKHD-545-35-K that you referenced is a Lithium based grease. When it's time to re-grease them we recommend the LMX red grease part # L11390 which is waterproof and the heavy duty. view full answer...
Yes. the Bearing Kit # BK2-100 is the correct kit for the 3,000lb axle under your 2010 Aliner Classic. If you determine your Hub/Drum # AKHD-545-35-K is worn we do have these you can replace. We also have the Left # AKEBRK-35L and Right # AKEBRK-35R brake assemblies if they also need replaced. view full answer...
I must recommend that you replace the hub/drum as well when changing the size of your braking assemblies because the surface area on the old drums may not line up with the new braking assemblies which is why I recommend replacing both at the same time.
The 10" x 1-1/2" braking assemblies part # K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you but we no longer have a correct hub for these.
The most common replacement for the 10"... view full answer...
For a torsion axle such as your Avan Aliner we have kits available that will give you some extra clearance.
The Avan Aliner is a single axle trailer, so we have two kits that will work for you. Torsion axles must be side-mounted and not top mounted and can not be used with Torflex axles with 3 inch high profiles.
The first one I recommend is The Torflex Lift Kit - Single Axle - 2-5/8 inch Lift # K71-707-01 which is compatible with #10 Torflex axles with 2,300 to 4,000 pound capacities.... view full answer...
Thanks for the information! The correct bearing buddies for your Dexter 3,000 lbs axle are the Bearing Buddy Bearing Protectors item # BB1980A-SS you were looking at. These are sold as a pair you will need one per axle. view full answer...
Yes, the Electric Trailer Brake Kit # AKEBRK-35-SA will replace the brakes that came on your 2013 Aliner Classic With the AL-KO axle. view full answer...
Go To Results